Oil press manufacturer: Do you know the accessories of combined oil press?

 


Ⅰ. Introduction to 6YL-100 combined oil press accessories.

6YL-100 combined oil press machine accessories specifically refer to pressing screw worms, pressing rings, pressing bars, cake output ring, gears, filter cloth, etc. In addition, there are also press shaft, press cage, gearbox, pressing roll, rails group ring, pressing cage minor key, pressing cage major key, press guide nut, tighting nut, adjusting bolt, spindle minor key, spindle major key, mandrel, sleeve, adjusting bolt hand, end nut.

Among these accessories of the oil press, some are extremely easy to wear due to their location in the oil press and their high frequency of use. These wearing parts include pressing screw worms, pressing rings, pressing bars, cake output ring, and gears. Therefore, when purchasing these vulnerable parts, pay attention to their wear resistance and corrosion resistance, as these have a direct impact on the service life of the accessories.

1. Dimensions of wearing parts of combined oil press

(1) 6YL-100 Pressing Screw Worms

There are 7 snails in each set. Screw No. 1-No. 2, length 126mm, diameter 95mm; Screw No. 3, length 129mm, diameter 95mm; Screw No. 4, length 50mm, diameter 95mm; Screw No. 5, length 100mm, diameter 95mm; Screw No. 6, length 110mm, diameter 95mm; Screw No. 7-cake guide ring, length 75mm, diameter 105mm

(2) 6YL-100 Pressing Rings

Each set of pressing rings has 16 pieces. There are three types of pressing rings: small, medium and big. The small pressing ring is 20mm, the medium pressing ring is 30mm, and the large pressing ring is 60mm.

(3) Vacuum oil filter spare parts

In addition to the same wearing parts as the screw oil press, the combined oil press also needs accessories for the vacuum oil filter, the most commonly used of which is filter cloth. Since the filter cloth needs to be replaced and cleaned regularly, you need to purchase several more sets of filter cloth. This will not affect the working efficiency of the oil filter.

If you need a separate accessory, you can give us the size of your original accessory. We also support customized accessories.

Ⅱ. How to dismantle and install 6YL-100 combined oil press accessories?

1. The method of dismantling screw worms.

Immediately after stopping the machine, move the handle, pull out the pressing shaft from the pressing chamber, remove the protective cap, hexagonal nut, round nut and adjusting bolt, insert an iron rod with a diameter of 16 into the hole of the locking nut and rotate it clockwise (remember to The threads of the shaft core are all left-handed). After removing the locking nut, each section of the screw can be removed. If the snail (with fine residue in the inner hole) is difficult to remove due to blockage, a wooden board can be placed on the ground and two people can gently bump the snail a few times to remove it. If it still cannot be removed, it can be heated with firewood and then removed. Remove.

2. Installation of screw worms.

Stand the pressing screw with its thin end upward, install the retaining ring, and install the pressing screws on the shaft in sequence starting from No. 1, and then tighten it with the locking nut to prevent the oil residue from going deep into the pressing screw hole and affecting the performance of the pressing screw. disassembly. (Adjust the nut so that both ends of the adjusting bolt are 8309 bearings. When installing, the large hole surfaces of the two bearings are against both ends of the adjusting bolt. After the press screw is assembled as a whole, use two (M42×62) nuts to back-tighten it. Pay attention to the gap between the two 8309 bearings. Turn the adjusting bolt by hand until you feel the rotation is flexible.

评论

发表评论

此博客中的热门博文

What do you need to know about the necessary knowledge of oil pressing machine?

图片
   Learn about oil extraction machines . There is a lot of oil presses in our daily lives.  Working principle 1. Peanut is a high oil-content crop. Its inner oil can be found in the cell as granular or spherical form. The closed film surrounds it. This film and cell wall become separated when the outside world squeezes them. Peanut oil will eventually flow from the crack. When the peanuts are squeezed by the outside, they become brittle and hard and lose their original elasticity. The peanut red coat is made up of more fibers and is separated from its surface using pressure. 2. You should apply different pressures depending upon the required fat content. Peanuts can be defatted with different effects. Peanut oil processing craft Process requirements: Peanuts must be degreased at more than 50%. Peanuts are free from broken particles and have no adhesion. The main factor that impacts the degreasing result is moisture. Second is the time. The best conditions to degrease effect are 4.52%
阅读全文

Open oil mills make it possible to produce safe and hygienic oils using oil press equipment.

 The daily life of everyday people is affected greatly by edible oil. The current market for edible oil has a poor quality. Some oil are mixed with crude oil. In order to buy edible oil, many consumers trust the freshly squeezed oil. miller oil company A major advantage of fresh squeezed edible oil that is sold is the fact that it can be inspected throughout its production. The squeezed edible oils are directly mixed with oil, so they don't have to be added to any other products. oil mill The people are able to recognize when the oil mill is opened to allow the oil press equipment achieve hygienic output. The people have always been able to trust the production method of on-site oil press sales. On this subject, certain raw materials are being imported. oil filter machine repair The oil's craftsmanship and the falsified ingredients will cause people to be suspicious. People won't recognize oil mills. Oil mills must be able to continue their long-term success. It must be pro
阅读全文

Large Oil Presses Maintenance Plan.

图片
Oil pressing business is improving. More customers are now purchasing large oil pressing machines. The screw oil presse is now more in demand. After the oil presses have been used for some time, you will experience problems such as this. It is important to maintain large oil presses. Let's learn how to maintain large oil presses at peacetime.  Large Oil Presses Maintenance Plan  1. Once you have purchased the oil press, you must install, debug it, and use it in strict conformance with the instructions.  2. The oil press must be kept in a well-lit area and in a comfortable working environment.  3. Oil press problems must be addressed immediately. It is best to hire someone who is familiar with operating oil presses or a professional to do maintenance.  4. Cover the screw oil press cage with tarpaulin so that dirt and dust do not get into the gaps in the accumulation bars.  5. The oil tank for the seed oil press must be kept clean. It should be regularly cleaned and the oil shoul
阅读全文